Men-luck

Fine work, quality first

Service and support

Men-Luck is one of the top high-precision laser equipment manufacturers in China.

  • Connect the chiller, power on, ventilate and water, check whether the gas circuit leaks, whether the voltage flows, whether the chiller is cooled, whether the laser emits light, and whether the machine operates normally.
  • Set the program and let the machine run idle for about 2H to warm up.
  • Help customers adjust the machine: focus, concentricity and seam width are set to the parameters required by customers.
  • Proofing for customers can completely cut customers' products and meet customers' process needs. (upon acceptance at the factory, the parameters of the cut products can match the process of the products cut at the factory)
  • Machine nameplate marking
  • Finally, check whether the machine circuit, water circuit and air circuit are normal.
  • Package the machine.

  • 1 set of guide sleeve and bushing respectively
  • A pair of triangular supports
  • Two nozzles and one protective lens
  • 1 wet cut water pipe
  • 1 machine key
  • Finally, check whether the machine circuit, water circuit and air circuit are normal.
  • Package the machine.

Technical specifications, operation instructions for loading and unloading lenses of laser cutting head, operation instructions of laser cutting machine, software operation instructions, maintenance manual of laser cutting machine and circuit drawings.

Ground bearing 800kg/m²
Ambient temperature 20~30℃
Temperature change rate Max 1℃/hour
relative humidity 30% ~ 70% (no condensation)
Place the equipment Clean room (class 100000)
There are no high-frequency and noisy equipment around
There are no wiring and structures around that can transmit high frequency or noise
There is no high-frequency signal and noise that have an impact on electronic machinery around
There is no perceived vibration in the area where the equipment is placed (if there is vibrating equipment near the equipment placement area, vibration isolation treatment is required)
Power Supply 220V±10％
compressed air If it meets 0.8MPa and the air pressure is insufficient, the customer should be given reasonable suggestions in advance, such as buying a booster pump or using a gas cylinder.
Check the machine completely according to the inspection specifications
Connect the water chiller, power and gas, and check whether the operation of the water chiller is normal, whether the voltage flows, whether the air circuit leaks, whether the air pressure is normal, and whether the overall operation of the machine is normal.
The machine is warmed up and idled for 1H.
The after-sales personnel shall sample the customer's products and check whether the products from the sample are consistent with the products from the factory. If they are inconsistent, the after-sales personnel shall help the customer debug and pass the test.
Operation training The operator and maintenance personnel shall be trained on the operation and daily maintenance of the equipment at your site. The number of trainees is 2, including 1 operator and 1 maintenance personnel. The training contents include graphic programming, laser principle, equipment structure, process description, daily equipment maintenance, laser safety protection, operation procedures and simple troubleshooting, etc. until the customer can operate the training contents by himself.
After the training, complete the handover.
After the delivery, the customer software will be permanently authorized.

The equipment shall be inspected once a year from delivery, and consumables shall be replaced during inspection.

The free warranty period of the equipment is 12 months, calculated from the date of signing the acceptance certificate by both parties, and our company will send engineers to provide after-sales service. Outside the warranty period, our company will provide maintenance service and technical support in the form of charge according to your maintenance requirements.

Our company can prepare the equipment for normal operation under the condition that your company carries out appropriate warranty management and correct operation in accordance with the relevant matters and conditions described in the operation manual.

  • The connection between our equipment and your related supporting equipment (power supply, gas supply, etc.) is not smooth
  • Parts or equipment are damaged as a whole due to incomplete warranty management and incorrect operation
  • Carry out product processing beyond the specified specifications.
  • The equipment is modified without the consent of our company.
  • Damage to equipment caused by earthquake, fire, flood, lightning and other force majeure factors.
  • Other damages not caused by our responsibility:Optical components, warning lights and other consumables are not covered by the warranty.Our company is not responsible for your production loss, loss of other assets, personal injury and other indirect injuries.
  • Failure to carry out regular spot inspection of item 4.3 in time.

Do you have any questions?